17 Reasons Why You Shouldn t Ignore Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are easy to maintain and are durable and long-lasting. They do not decay or rust as timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will save you from costly repairs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home, and could even be fatal. It is crucial to take the time to ensure that you're doing all you can to ensure that your windows are in good repair.

For single pane windows, it can be relatively simple to replace them, and the replacement will usually fit inside the old frame very easily. If you have double-paned windows which are held together by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this instance you'll need to locate some plastic spacers that aid the new pane in being able to fit perfectly into the window frame.

Wearing eye protection and heavy gloves is essential if you plan to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall onto the fabric, not onto the floor which could cause them to be trampled.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block water and drafts from getting into the home until a professional comes out and repair the window. It also acts as an obstacle to stop criminals from getting into your home. If the gap is large, you may want to consider using a security door that has an integrated window, as it offers the best of both worlds.

2. Sagging

Upvc windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber windows made of sash. However, with time, they may be afflicted by a variety of issues, including sliding. A sagging window can cause problems with light, draughts or even security. It's important to take action when you notice your uPVC windows are sagging.

Repositioning the hinges could aid in fixing a window that is sliding. You'll first need to open the windows to access the frame. After that, using a screwdriver, you can remove the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after having repositioned your hinges. If you're satisfied with the size of the window repair, you can tighten screws to secure them in the right position.

If you are unable to reposition the hinges, you may have to replace the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loosen. If this happens, it's crucial to replace the seal as fast as possible to ensure your uPVC windows remain watertight and secure from draughts.

UPVC handles can also become loose. This is usually due to screws that have been removed over time, but it could also be caused by the handle mechanism getting worn out. Luckily, it's not difficult to fix the handle of a window that is loose yourself. First, you'll need to shut the window and perform an experiment fitting. The joints at the corners of the sash should be aligned with the joint on the casing. If it doesn't, you can use a screwdriver or a wrench to loosen the handle and then return the mechanism to its original its original position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains, it is important that you take action. The leaks of water from windows do can not only cause destruction of your home's structure but also hinder your efforts to regulate the temperature inside your home. The most common cause for leaks in upvc window repair near me windows is that the sealant surrounding the frame is either damaged or not present.

This is a fairly simple fix that can be completed by any competent DIYer. Depending on the severity of the issue the caulking that was used up may need to be removed before a new layer of caulk can be put on. It is crucial to keep in mind that when it is about uPVC window repairs, do not be tempted to apply too much caulk and then make the area harder to clean and reduce your energy efficiency.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more severe cases, you may need to replace the window.

Other indicators of water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in humid conditions and can propagate quickly throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely the issue is more with the seal than the frame. Again this can easily be fixed by an uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or it blows open with an ease. These are easily repaired by any DIYer who is skilled and can usually be done within a few minutes.

Like any mechanical component hinges are prone to wear out over time. Changing a window hinge is essentially a simple procedure, but it is easier to do if you have someone to help hold the frame in place.

It is also worth checking that the uPVC hinges are being opened and closed in the correct direction. This can be done by looking for the arrows on each hinge. This shows which way the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a particular way or by poor installation at the factory. This issue can be fixed by sending us a photo through our website and we will be happy to give you suggestions.

Regularly lubricating the hinges is also necessary. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication will make the window easier to open and close. It also decreases the possibility of a window getting stuck and stop corrosion. The ideal time to perform this every year. WD40 and other solvent-based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a few various factors. The hinges can also be unbalanced due to wear, creating gaps where the sash meets frame. This can be easily repaired by giving them good clean, but if they are beyond repair it could be necessary to get them re-aligned or replaced. Secondly the interlock, this is located on the hinge of the window, may also become misaligned, again it may be possible to just give them a good clean, but in certain cases, it may be necessary to have these replaced.

The second most frequent cause of draughts is the window seals. They are prone to wear or damaged over time, and allow air to escape through the gaps. Installing high-quality weatherstripping will help to stop draughts. Another alternative is to replace the upvc window with low-emissivity glass, this will help to regulate indoor temperatures and again will reduce draughts.

One of the most effective ways to cut down on drafts is to use an draught excluder. These are typically made of fabric which are filled with a sort of filler and can be placed on the windowsill on top. They will keep your home warm by blocking cold air.

Your upvc windows can continue to provide excellent insulation and security in your home with a little regular maintenance and repairs. It is crucial to realize that windows last for a certain period of time and they may reach an point at which it is more cost-effective to replace them rather than fix them. If you are experiencing issues with your Upvc windows, it's recommended to seek assistance from a professional immediately.