14 Businesses Doing A Superb Job At Patio Door Lock Repair
Patio Door Lock Repairs
Over time, patio doors experience wear and tear that can cause locks that fail. However, there are simple and efficient ways to restore your uPVC patio door's security.
It's about realigning the lock or cleaning the mechanism that locks these simple fixes will make your home more secure.
Clean the Lock
While patio doors are a great way to bring the outside in and keep out the elements but they can also pose an issue for security when your lock isn't functioning as it should. Over time, wear and tear, cold and hot weather dirt and debris can take their toll on your patio door's lock and make it difficult to open. Fortunately, with a little care you can make sure that your patio door's locks always perform correctly.
It's important to first clean the patio glass repair door lock as well as all moving parts. This will help get rid of any coatings or dirt that could be preventing the lock from working correctly. Begin by wiping all the moving parts of your patio door's lock using a damp cloth. then employ a scouring pad or rough damp cloth to scrub any hard-to-reach parts of the door and frame that are coated with dirt. It is recommended to wipe the entire lock with dry cloths to eliminate any remaining dampness, and allow it to air dry prior to making use of it again.
If you have an exterior door that is fitted with pin tumbler latch mechanisms You can grease the lock by applying powdered graphite to the key or by using a Teflon-based lubricant such as WD-40 Multi-Use Product. This type of lubricant can be applied with ease and does not dissolve over time. If you're unable to find an appropriate lubricant you can try using a pencil with a thick tip. Put the pencil into the lock and move it around to spread the graphite.
The tracks for sliding patio doors repair patio doors also require regular maintenance to keep them free of dirt, dust and other debris. They are particularly susceptible to ice and snow which could cause them to jam or bind and make it difficult for your patio doors to open and close.
Clean the track rails and rollers on sliding patio doors by removing any damaged or dirty weather stripping. Clean it, then replace it. The rollers for patio doors can be cleaned and sprayed down with an oil that is nonstick.
Lubricate the Moving Parts
uPVC French Doors, like sliding patios, operate by using 3 to 4 or sometimes, 5 point locking mechanisms. This includes the handle and lock cylinder which is operated by keys. They require maintenance and oiling of the moving parts. This can be accomplished with the use of a thin oil but not WD40. It should be done every year, at a minimum.
If hinges that are sagging don't cause the issue it could be because the door isn't aligned. It could be rubbing or catching the hole of the strike plate in the frame. Take off the strike plate and use a sharp tool to increase the size of the mortise. This allows the latch to sit properly in the hole, and also prevents rubbing or catching on the frame.
Measure the width of the cylinder with a piece of wood or a book that can be inserted into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end of the of the cylinder.
Check the width of the lock.
If your patio door latch isn't able to turn even after cleaning and lubricating, there's a possibility that it's not in alignment with the strike plate hole. Check to see if the door is properly balanced and if the hinge screws are tight, but in many cases shifting the strike plate upwards or downwards can fix the issue.
The latch may not be able to engage properly in the event that the strike of the lock is not large enough. In this case, enlarge the opening with the hammer and chisel. Then, test the latch to ensure that it doesn't rub against the jamb frame of the door or get caught the frame.
You must identify the kind of mortise lock you have before buying an alternative. This can be done by looking at the faceplate and determining if it is square or round. Then, look at the screw holes in the existing lock and note the dimensions of each. This information will aid you in finding an alternative that is of the same size and is a perfect fit for the hole you have already.
You'll want to identify the mortise lock and examine it for any bends, scratches or other damage that requires to be repaired. A damaged or bent latch is more likely break than one that's been utilized often, so make sure to replace the lock with a brand new one that is secure if you find any signs of wear or damage.
Once you've checked the lock and identified which type of replacement you'll need, it's time to start working on the actual repair. Take the old handle and spindle out of your patio door, and then install the new one. Start by putting in the handle in the interior and aligning it with the spindle, and then fixing it by using the two bolts or screws that secure it. Install the exterior handle following the interior handle. After you've completed the steps you can test the new handles to ensure that they open and close easily and that the latch locks correctly when you strike the plate.
Check the door's Strike
The strike plate and door latch are two parts that work together in order to lock the door. Misaligned strike plate and door latch will result in the latch not being able to latch the door correctly. Fortunately, this issue is usually simple to fix.
Check the holes for receiving of the strike plate to ensure they are clear of obstructions, such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move vertically, but not removing it from the frame of your door. Adjust the strike plate to align its holes for receiving with latch hooks of the door latch. Once the strike plate is adjusted tighten the screws, and then test the door to determine whether it shuts easily with the new adjustment.
These plates are difficult to reach for homeowners with sliding patio doors. However they are crucial to lock and unlock your door. The metal plates are typically located at the top and bottom of the door jamb, which is where they are used to support the door's latch. The door latch slides onto the strike plate and forms a seal. If the strike plate is damaged, rusted or not installed correctly, it may prevent the latch from locking the door securely.
The most common reason for the patio door lock to become stuck or not close is a misalignment between the latch and strike plate. The easiest method to check for this is to perform the "lipstick test." Rub some lipstick on the outside of the deadbolt and put masking tape on it. The lipstick will leave a mark when you close the door. This will indicate exactly where the latch joins the strike plate. If the mark is too low or high it is possible to adjust the strike plate.
Sliding patio door locks help keep your home safe from burglars, and if they're not working correctly, you must repair the issue quickly. Follow these simple steps to fix your patio door lock and restore its function.